[R-meta] Testing interaction term of categorical moderators in rma.mv

[Ju Lee]

Dear Wolfgang and all,

I am writing to ask a question of how I could perform the test to acquire main interaction effect of two categorical moderators (that have 3 and 2 levels each)
I have been referring to http://www.metafor-project.org/doku.php/tips:multiple_factors_interactions to do this, but have been troubled how to proceed.

1) In the post, Wolfgang suggests:

"To test whether the interaction is significant in general, you can either do a Wald-type test with:

rma(yi, vi, mods = ~ factor(catmod1)*factor(catmod2), data=some.data.frame, btt=X:Y)

where X is the number of the first "interaction coefficient" and Y is the number of the last "interaction coefficient" (so, these are indices to indicate which coefficients should be tested simultaneously). In the output, you will the results of this test under "Test of Moderators�.�

 However, I am not sure how I can specify the first and last coefficient of interaction terms from a output below. I would deeply appreciate if you could help me figure this out.


> r1<-rma.mv(hedged,VCV, mods=~ Region * Consumption.level, method="ML", random = ~ region.cl |   Study, data=MHF, struct="DIAG", subset=(!is.na(region.cl)))

>r1

Multivariate Meta-Analysis Model (k = 841; method: ML)

Variance Components:

outer factor: Study     (nlvls = 176)
inner factor: region.cl (nlvls = 6)

            estim    sqrt  k.lvl  fixed                    level
tau^2.1    0.6893  0.8302    113     no    High latitude:Primary
tau^2.2    0.6354  0.7971    380     no  High latitude:Secondary
tau^2.3    1.1672  1.0804    211     no   High latitude:Tertiary
tau^2.4    1.2214  1.1052     80     no     Low latitude:Primary
tau^2.5    0.0000  0.0001     16     no   Low latitude:Secondary
tau^2.6    0.3215  0.5670     41     no    Low latitude:Tertiary

Test for Residual Heterogeneity:
QE(df = 835) = 3679.1163, p-val < .0001

Test of Moderators (coefficient(s) 2:6):
QM(df = 5) = 21.9742, p-val = 0.0005

Model Results:

                                               estimate      se     zval    pval    ci.lb   ci.ub
intrcpt                                          0.3007  0.1904   1.5788  0.1144  -0.0726  0.6739
RegionLow latitude                              -0.4096  0.3263  -1.2552  0.2094  -1.0491  0.2300
Consumption.levelSecondary                       0.2006  0.2156   0.9303  0.3522  -0.2220  0.6232
Consumption.levelTertiary                        0.7136  0.2497   2.8577  0.0043   0.2242  1.2031  **
RegionLow latitude:Consumption.levelSecondary    0.1687  0.3523   0.4787  0.6322  -0.5219  0.8593
RegionLow latitude:Consumption.levelTertiary    -0.1613  0.4201  -0.3838  0.7011  -0.9847  0.6622

---
Signif. codes:  0 �***� 0.001 �**� 0.01 �*� 0.05 �.� 0.1 � � 1

2) Secondly, as an alternative Wolfgang suggests using likelihood-ratio test with full (with interaction term) and reduced (without interaction term) models to test the significant interaction.

However, all my models are based on �REML� method, and apparently I need to fit models with �ML� to do the above test. Is it appropriate if conduct LRT for interaction using �ML�, but keep the rest of my analysis using �REML� method?

Thank you for reading, and I sincerely hope to hear back from you.

Best regards,
JU



	[[alternative HTML version deleted]]