[R-sig-Fedora] 答复: 答复: how can I know the version of my zlib checked by R

[nw宁威]

Dear Martyn,

	I'm really grateful to you and your useful suggestions! I will try and tell you a good news once I accomplish the installation.

Best Regards

Wei Ning
Ctrip, Shanghai

-----邮件原件-----
发件人: Martyn Plummer [mailto:plummerm at iarc.fr] 
发送时间: 2017年2月7日 19:02
收件人: r-sig-fedora at r-project.org; nw宁威 <wning at Ctrip.com>
主题: Re: 答复: [R-sig-Fedora] how can I know the version of my zlib checked by R

On Tue, 2017-02-07 at 10:13 +0000, nw宁威 wrote:
> Dear Martyn,
> 
> 	Thank you so much for your suggestion. Can I install R by rpm WITHOUT 
> Internet? This Linux server cannot connect to web.

The same mechanism you used to transfer the source tarball to the server can be used for the EPEL RPMs and then you can do a local install with yum.

You will have to go through a long iterative process of identifying missing dependencies (yum will tell you) transferring the corresponding RPMs to the server and installing them. But it will still be better than installing from source.

Martyn

> Best Regards
> 
> Wei Ning
> Ctrip, Shanghai
> -----邮件原件-----
> 发件人: Martyn Plummer [mailto:plummerm at iarc.fr]
> 发送时间: 2017年2月7日 17:17
> 收件人: r-sig-fedora at r-project.org; nw宁威 <wning at Ctrip.com>
> 主题: Re: [R-sig-Fedora] how can I know the version of my zlib checked 
> by R
> 
> On Tue, 2017-02-07 at 08:39 +0000, nw宁威 wrote:
> > 
> > Hi, professors
> > 
> >          I'd like to install R-3.3.2 from .tar.gz on my linux 
> > system(CentOS 6.4). When installing, R told me that the version of 
> > zlib was too old.
> 
> Do you really need to install from source? The EPEL RPMs by Tom 
> Callaway from Redhat contain a bundled version of zlib for platforms 
> that do not have an up-to-date system version, and so are much easier 
> to install.
> 
> Note that it is not only zlib that is affected. You will have the same 
> issue for bzip, xzv, pcre, and curl.
> 
> > 
> >          So, I eager to know which version of zlib did R-3.3.2 
> > software examine at its configure step. How could I check the 
> > version of zlib? I will appreciate a lot if you could do me a 
> > favour.
> 
> This information is contained in the "R Installation and 
> Administration" manual, also known as "R-admin". The minimum version 
> required is zlib 1.2.5.  You can also see this information in the 
> output from configure, e.g. on my system:
> 
> checking if zlib version >= 1.2.5... yes
> 
> Martyn
> 
> > 
> > Best Regards
> > 
> > Wei Ning
> > Ctrip, Shanghai
> > 
> > 	[[alternative HTML version deleted]]
> > 
> > _______________________________________________
> > R-SIG-Fedora mailing list
> > R-SIG-Fedora at r-project.org
> > https://stat.ethz.ch/mailman/listinfo/r-sig-fedora