optimize {stats} | R Documentation |

The function `optimize`

searches the interval from
`lower`

to `upper`

for a minimum or maximum of
the function `f`

with respect to its first argument.

`optimise`

is an alias for `optimize`

.

```
optimize(f, interval, ..., lower = min(interval), upper = max(interval),
maximum = FALSE,
tol = .Machine$double.eps^0.25)
optimise(f, interval, ..., lower = min(interval), upper = max(interval),
maximum = FALSE,
tol = .Machine$double.eps^0.25)
```

`f` |
the function to be optimized. The function is
either minimized or maximized over its first argument
depending on the value of |

`interval` |
a vector containing the end-points of the interval to be searched for the minimum. |

`...` |
additional named or unnamed arguments to be passed
to |

`lower` |
the lower end point of the interval to be searched. |

`upper` |
the upper end point of the interval to be searched. |

`maximum` |
logical. Should we maximize or minimize (the default)? |

`tol` |
the desired accuracy. |

Note that arguments after `...`

must be matched exactly.

The method used is a combination of golden section search and
successive parabolic interpolation, and was designed for use with
continuous functions. Convergence is never much slower
than that for a Fibonacci search. If `f`

has a continuous second
derivative which is positive at the minimum (which is not at `lower`

or
`upper`

), then convergence is superlinear, and usually of the
order of about 1.324.

The function `f`

is never evaluated at two points closer together
than `\epsilon`

` |x_0| + (tol/3)`

, where
`\epsilon`

is approximately `sqrt(.Machine$double.eps)`

and `x_0`

is the final abscissa `optimize()$minimum`

.

If `f`

is a unimodal function and the computed values of `f`

are always unimodal when separated by at least `\epsilon`

` |x| + (tol/3)`

, then `x_0`

approximates the abscissa of the
global minimum of `f`

on the interval `lower,upper`

with an
error less than `\epsilon`

` |x_0|+ tol`

.

If `f`

is not unimodal, then `optimize()`

may approximate a
local, but perhaps non-global, minimum to the same accuracy.

The first evaluation of `f`

is always at
`x_1 = a + (1-\phi)(b-a)`

where `(a,b) = (lower, upper)`

and
`\phi = (\sqrt 5 - 1)/2 = 0.61803..`

is the golden section ratio.
Almost always, the second evaluation is at
`x_2 = a + \phi(b-a)`

.
Note that a local minimum inside `[x_1,x_2]`

will be found as
solution, even when `f`

is constant in there, see the last
example.

`f`

will be called as `f(`

for a numeric value
of `x`, ...)`x`.

The argument passed to `f`

has special semantics and used to be
shared between calls. The function should not copy it.

A list with components `minimum`

(or `maximum`

)
and `objective`

which give the location of the minimum (or maximum)
and the value of the function at that point.

A C translation of Fortran code https://netlib.org/fmm/fmin.f
(author(s) unstated)
based on the Algol 60 procedure `localmin`

given in the reference.

Brent, R. (1973)
*Algorithms for Minimization without Derivatives.*
Englewood Cliffs N.J.: Prentice-Hall.

```
require(graphics)
f <- function (x, a) (x - a)^2
xmin <- optimize(f, c(0, 1), tol = 0.0001, a = 1/3)
xmin
## See where the function is evaluated:
optimize(function(x) x^2*(print(x)-1), lower = 0, upper = 10)
## "wrong" solution with unlucky interval and piecewise constant f():
f <- function(x) ifelse(x > -1, ifelse(x < 4, exp(-1/abs(x - 1)), 10), 10)
fp <- function(x) { print(x); f(x) }
plot(f, -2,5, ylim = 0:1, col = 2)
optimize(fp, c(-4, 20)) # doesn't see the minimum
optimize(fp, c(-7, 20)) # ok
```

[Package *stats* version 4.2.2 Index]